M241 1 form a solid state rela y the M241 is a bi-directional, single-pole, single-throw, normally open multipurpose solid-state relay in a miniature 4-pin smal l outline package. it is designed to replace electromechanical relays in general purpose switching applicat ions. the relay consists of an integrated circuit that drives two rugged source-to-source enhancement type dmos transistors - optically coupled to a light emitting diode . the output mos transistors are protected with free-wheeling diodes that can handle up to 5a of inrush current, making the relay ide al for switching lamps and highly inductive loads. description features applications options/suffixes* schematic diagram absolute maximum ratings* approvals miniature 4 pin sop package ? low input power consumption (2.5ma typ) ? 150ma maximum continuous load current ? 8 ohms maximum on-resistance ? blocking voltage 200v ? long life/high reliability ? multiplexers ? meter reading systems ? data acquisition ? medical equipment ? battery monitoring ? home/safety security systems ? tape and reel (2,000 pcs per reel) ? -tr note: suffixes listed above are not included in marking on device for part number identification. parameter unit min typ max storage temperature c -55 125 operating temperature c -40 85 continuous forward current ma 50 peak forward current (1us) a 1 reverse input control voltage v 5 output power dissipation mw 400 *the values indicated are absolute stres s ratings. functional operation of the device is not implied at these or any conditions in excess of those defined in electrical characteristics section of this document. exposure to absolute ratings may cause permanent damage to the device and may adversely affect reliability. ul / c-ul approved: file e201932 ? www.ssousa.com ? +1.408.293.4600 page 1 of 5 M241 rev 1.43 (2/9/2010) ? 2010 solid state optronics ? san jos, ca
M241 1 form a solid state rela y electrical characteristics - 25c parameter unit min typ max test conditions input specifications led forward voltage v 1.2 1.5 if = 10ma led reverse voltage v 612 ir = 10ua turn-on current m 2.5 5 io = 150ma a turn-off current m 0.5 a output specifications blocking voltage v 200 io = 1ua continuous load current m 150 if = 5ma a on-resistance : 5 8 io = 150ma leakage current p 0.2 1 vo = 100v a output capacitance p 25 50 vo = 25v, f = 1.0mhz f offset voltage m 0.2 if = 5ma v coupled specifications isolation voltage v 1500 t = 1 minute turn-on time m 1.5 3 if = 5ma, io = 150ma s turn-off time m 0.05 0.5 if = 0ma, io = 150ma s isolation resistance g 100 : coupled capacitance p 2 f contact transient ratio v 2000 7000 dv = 50v / p s www.ssousa.com ? +1.408.293.4600 page 2 of 5 M241 rev 1.43 (2/9/2010) ? 2010 solid state optronics ? san jos, ca
M241 1 form a solid state rela y performance data 0 10 20 30 40 0 0.040.040.040.050.050.050.05 turn-off time (ms) device count M241 typical turn-off time distribution n = 100, ambient temperature = 25c 0 10 20 30 40 4.4 4.5 4.6 4.7 4.8 4.9 5 5.1 on-resistance (ohms) device count M241 0 10 20 30 40 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 leakage current (ua) device count typical on-resistance distribution n = 100, ambient temperature = 25c M241 typical leakage current distribution n = 100, ambient temperature = 25c 0 10 20 30 40 190 200 210 220 230 240 250 260 blocking voltage (v) device count M241 0 50 100 150 200 -40 -20 0 20 40 60 80 temperature (c) load current (ma) typical blocking voltage distribution n = 100, ambient temperature = 25c M241 maximum load current vs. temperature 0 10 20 30 40 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 turn-on time (ms) device count M241 typical turn-on time distribution n = 100, ambient temperature = 25c www.ssousa.com ? +1.408.293.4600 page 3 of 5 M241 rev 1.43 (2/9/2010) ? 2010 solid state optronics ? san jos, ca
M241 1 form a solid state rela y mechanical dimensions 4 pin small outline package end view top view back view www.ssousa.com ? +1.408.293.4600 page 4 of 5 M241 rev 1.43 (2/9/2010) ? 2010 solid state optronics ? san jos, ca
M241 1 form a solid state rela y solid state optronics (sso) makes no warranties or representations with regards to the completeness and accuracy of this docume nt. sso reserves the right to make changes to product description, specifications at any time without further notice. sso shall not assume any liability arising out of the appl ication or use of any product or circuit described herein. neither ci rcuit patent licenses nor indemnity are expressed or implied. except as specified in sso's standard terms & conditions, sso disclaims liability for consequential or other damage, and we mak e no other warranty, expressed or implied, including m erchantability and fitness for particular use. disclaime r life support polic y sso does not authorize use of its devices in life support applications wherein failure or malfunction of a device may lead to p ersonal injury or death. users of sso devices in life support applications assume all risks of such use and agree to indemnify sso against any an d all damages resulting from such use. life support devices are defined as devices or systems which, (a) are intended for surgical im plant into the body, or (b) support or sustain life, and (c ) whose failure to perform when used properly in accordance with instructions for u se can be reasonably expected to result in significant injury to the user, or (d) a critical component in any component of a life support device or system whose failure can be reasonably expected to caus e failure of the life support device or system, or to affect its safety or effe ctiveness. www.ssousa.com ? +1.408.293.4600 page 5 of 5 M241 rev 1.43 (2/9/2010) ? 2010 solid state optronics ? san jos, ca
|
